
An Orlando driveway with a sound base but a sun-faded top is often a fair asphalt resurfacing and overlay job. We mill the worn surface, tack the old asphalt, and lay a new binder and surface course pitched toward the nearest retention pond. Most driveways in the Orlando area, from the in-town bungalows of College Park and Thornton Park to the sprawling subdivisions around Lake Nona and Dr. Phillips, sit on deep Central Florida ridge sand over porous limestone. That base drains fast, but the top layer takes a beating from daily summer thunderstorms, intense UV, and the occasional hurricane rains that pool in low spots. A resurfacing extends the life of a driveway with a solid foundation by five to ten years, costs less than full replacement, and is the right call when alligator cracking is light to moderate and the base has not failed. We handle resurfacing and overlay work across Orlando, Winter Park, Kissimmee, Sanford, and surrounding areas, with free estimates and written tonnage specs on every job.
Why Asphalt Resurfacing & Overlay Matters in Orlando's Climate
Central Florida's heat and humidity accelerate oxidation of asphalt. The sun fades the binder, and standing water from summer thunderstorms seeps into hairline cracks and weakens the base. A driveway that is ten to fifteen years old often shows surface wear but has a base that is still structurally sound. Resurfacing addresses the visible damage, restores drainage pitch, and buys time before a full replacement becomes necessary. The difference between a patch job and a resurfacing job is surface area: once alligator cracking covers more than thirty to forty percent of the drive, patching throws money away, and resurfacing becomes the honest choice.
- We mill the worn asphalt to remove the oxidized top layer and create a clean, stable surface for new material.
- We tack the old asphalt with a bonding agent to ensure the new binder course adheres firmly and does not slip under load.
- We lay a new binder course, typically two inches, to provide structural depth and flexibility.
- We finish with a surface course pitched to shed water toward drainage areas, swales, or retention ponds.
- We compact the entire surface with vibratory rollers to lock the aggregate and ensure durability.
A properly executed resurfacing restores the driveway's ability to shed water and resists cracking for years.
Local example: A fifteen-year-old driveway in Winter Park with light alligator cracking and a solid base is a textbook resurfacing candidate. A similar driveway in Kissimmee with extensive cracking, rutting, and soft spots under the wheels is heading toward full-depth replacement. The difference is visible on site and determines whether resurfacing will hold or whether the money belongs in replacement.
For more on the decision between repair and replacement, see our guide to driveway replacement in Orlando.
How We Execute Asphalt Resurfacing & Overlay in Orlando
A resurfacing job begins with a site walkthrough. We measure the driveway, assess the base for soft spots or settlement, check drainage pitch, and identify any utilities that must be marked before milling begins. Florida 811 utility locates are required by law before any excavation or milling. We then schedule the work, mill the surface, apply tack, and lay the new asphalt in two courses, compacting each pass. The job typically takes one to two days, depending on size and weather.
- We schedule a free on-site estimate, measure the driveway, and provide written tonnage and thickness specs.
- We request Florida 811 utility locates before any milling or excavation work begins.
- We mill the worn asphalt to a depth that removes the oxidized layer and exposes a clean, stable base.
- We apply a tack coat of bonding agent to the milled surface to lock the new asphalt in place.
- We lay the binder course, typically two inches, in a single pass with a paving machine.
- We finish with the surface course, typically one to one and a half inches, and compact with vibratory rollers.
- We verify pitch and drainage before the job is signed off, ensuring water sheds away from the home.
New asphalt should not be sealed for at least six to twelve months while it cures and hardens.
Local example: A Sanford homeowner with a 2,000-square-foot driveway showing light alligator cracking received a resurfacing estimate of 4 inches of new asphalt (binder plus surface), scheduled for early April. The job took one day, the driveway was reopened to traffic the next morning, and the homeowner avoided the cost and disruption of a full-depth replacement.
To understand the full scope of driveway repair options, visit our driveway repair page.
Resurfacing Methods: Overlay vs. Mill and Overlay
| Approach | Description | Best for |
|---|---|---|
| Mill and Overlay | Remove the worn top layer, tack, and lay new binder and surface. Restores drainage pitch and removes oxidized material. | Driveways with sound bases, light to moderate alligator cracking, and poor drainage pitch. |
| Overlay Only | Lay new asphalt directly over the existing surface without milling. Faster and cheaper but does not address drainage or oxidized material. | Lightly worn driveways with good drainage and no cracking. Rare in Central Florida due to heat and UV. |
| Full-Depth Replacement | Remove all asphalt, prepare and compact the base, and lay new asphalt from the ground up. Required when the base has failed or sunk. | Driveways with extensive cracking, settlement, soft spots, or a base compromised by water or sinkholes. |
| Milling for Recycling | Remove asphalt and recycle it as crushed millings for base prep, gravel drives, or pothole repair. No new paving. | Driveways being replaced with concrete, gravel, or recycled asphalt. Also used for base material on other projects. |
Mill and overlay is the most common resurfacing approach in Orlando because our climate and drainage challenges make milling necessary to restore pitch and remove oxidized material.
Asphalt Resurfacing & Overlay Cost in Orlando: What to Expect
Resurfacing costs in Orlando typically start at $4 per square foot for mill and overlay on a straightforward residential driveway. A 2,000-square-foot drive runs roughly $8,000 to $10,000 before any site-specific factors. The final price depends on the depth of milling required, the condition of the base, drainage complexity, whether utilities need locating, and site access. A driveway with soft spots or settlement may require additional base prep, which increases cost. A long, narrow drive in an older neighborhood with mature trees and tight access costs more to mill and compact than a wide, open drive in a newer subdivision.
We provide free, written estimates that include measured square footage, milling depth, tonnage of new asphalt, and a fixed price. We recommend getting two or three estimates from local contractors to compare approach, materials, and pricing. A price that is significantly lower than others should raise a question: is the contractor milling to the right depth, using the correct binder thickness, or simply laying a thin overlay that will not last?
Permit costs vary by municipality. Some Orlando-area cities require a driveway permit; others do not. We help homeowners navigate local permitting and can advise on whether your address falls inside a jurisdiction that requires one. For more detail on pricing and what is included at each tier, visit our full pricing overview.
Asphalt Resurfacing & Overlay Near Me: What Orlando Homeowners Should Know When Hiring a Contractor
Choosing a paving contractor is one of the largest decisions a homeowner makes on a driveway. The historic fraud in this trade is the unsolicited door-to-door pitch: a crew with out-of-state plates, a claim that they have leftover asphalt from a nearby job, a price that seems too good, a request for a large cash deposit, and no written contract. The best defense is to verify any contractor's credentials, get everything in writing, and check references from local work.
Before you sign a contract, ask the contractor about licensing and insurance requirements in your city or county. Florida places residential driveway paving in no state contractor license category, but many counties and cities still require local permits for driveway and apron work, and some counties require a valid contractor license for work that needs a county permit. Visit your local building department website or call to confirm what is required in your jurisdiction. Ask the contractor to provide proof of insurance and a written estimate that includes milling depth, tonnage, asphalt thickness, and a fixed price. Request references from recent driveway work in your area, and follow up with at least two of them. If your driveway is inside an HOA community, confirm that the contractor understands your HOA's architectural standards and can provide any required approvals or documentation.
- Verify that the contractor is fully insured and can provide a certificate of insurance before work begins.
- Ask for a written estimate that includes measured square footage, milling depth in inches, tonnage of new asphalt, and a fixed price with no hidden costs.
- Request references from recent jobs in Orlando, Winter Park, Sanford, or your local area, and call at least two.
- Confirm that the contractor understands local permitting and can advise whether a permit is required in your jurisdiction.
- If you live in an HOA community, verify that the contractor can work within your architectural guidelines and provide any required approvals.
- Never sign a contract or pay a large deposit without a written agreement that spells out the scope, timeline, materials, and price.
We are a locally based paving contractor in Orlando with a local address and local plates. We have been in business since 2014 and provide free estimates with written tonnage and thickness specs on every job. To schedule a free estimate or ask questions about your driveway, call us at (321) 352-4836 or visit our contact page.
Asphalt Resurfacing & Overlay in Orlando: Pricing Guide
| Service | Price | Details |
|---|---|---|
| Mill and Overlay Resurfacing | Starting at $4/sq ft | Includes milling, tack coat, binder course, and surface course on sound base with light to moderate cracking |
| Overlay Only (No Milling) | Starting at $2.50/sq ft | New asphalt laid directly over existing surface, used only when base is sound and drainage is adequate |
| Base Preparation & Drainage | On estimate | Required when soft spots, settlement, or poor pitch must be corrected before new asphalt is laid |
| Utility Locating (Florida 811) | Included | Required by law before any milling or excavation; we request and coordinate all locates at no charge |
| Free Estimate | No charge | Written tonnage and thickness specs provided within 24 hours, no obligation to book |
Indicative pricing, the exact cost depends on square footage, finish, and site access. Free personalized estimate within 24h at (321) 352-4836.